muzic

This library encapsulates a DEFLATE and INFLATE engine to provide a set of compression APIs partially compatible with Zlib. Specifically, it supports Zlib-style streaming operation for both compression and decompression, and RFC-1950 wrapper for raw DEFLATE stream. The objectives of this library are simplicity and lightweight, rather than performance and comprehensiveness, so that it can be integrated on embedded platforms.

Supported Zlib APIs

Please also refer to the Zlib Manual for the complete description of APIs. Note that behaviors of functions in this library are not strictly identical to their Zlib counterparts, and differences are stated below.

DEFLATE

• int deflateInit(z_stream* strm, int level)

  Initializes the internal stream state for compression. Currently, parameter level is not used, but preserved for compatibility with Zlib.

• int deflate(z_stream* strm, int flush)

  deflate compresses as much data as possible, and stops when the input buffer becomes empty or the output buffer becomes full. For flush modes, currently, only Z_FULL_FLUSH and Z_FINISH are supported. When modes other than Z_FINISH is passed via flush, the behavior of this function is the same as when Z_FULL_FLUSH is passed.

• int deflateEnd(z_stream* strm)

  All dynamically allocated data structures for this stream are freed. This function discards any unprocessed input and does not flush any pending output.

INFLATE

• int inflateInit(z_stream* strm)

  Initializes the internal stream state for decompression.

• int inflate(z_stream* strm, int flush)

  inflate decompresses as much data as possible, and stops when the input buffer becomes empty or the output buffer becomes full. Currently, parameter flush is not used, but preserved for compatibility with Zlib. The behavior of this function is always similar to the Zlib counterpart being fed with the option Z_SYNC_FLUSH. When macro MZ_ZLIB_CHECKSUM is not defined, inflate returns Z_STREAM_END immediately after the last block is consumed. When macro MZ_ZLIB_CHECKSUM is defined, it will further consume a 4-byte adler32 checksum after the last block, and if this block is not presented, it returns Z_OK instead of Z_STREAM_END. This behavior is similar to the zlib counterpart when inflateInit() is called to initialize the stream. See section Zlib stream checksum for more information.

• int inflateEnd(z_stream* strm)

  All dynamically allocated data structures for this stream are freed. This function discards any unprocessed input and does not flush any pending output.

Structures and macros

z_stream is the only structure that Zlib exposed to users to interact with DEFLATE and INFLATE APIs. All fields are replicated with their original names, while only the first 7 fields are used, and the rest are dumb variables reserved for compatibility.

Macros representing states and flush modes are preserved. They can be found in zlib_comp.h.

Build and integration

The structure of this library is simple and flat, and no dependency other than libc is required. To use DEFLATE APIs, include zlib_comp.h and add defl_static.c, genlz77.c and zlib_comp.c to sources. To use INFLATE APIs, include zlib_comp.h and add inflater.c, zlib_comp.c to sources.

CMake is also supported. To use this library as a subproject, simply add muzic to target_link_libraries of targets depend on this library.

Notes

Zlib stream header

Zlib pads raw deflate stream with a 2-byte header conforming RFC-1950 by default. To emulate this behavior, the macro MZ_ZLIB_HEADER must be enabled in mz_config.h (it's enabled by default). Only when inflateInit2() and deflateInit2() are called with windowBits set to negative values, Zlib will generate and accept raw deflate stream without the header, and MZ_ZLIB_HEADER can be disabled. Otherwise, Zlib will signal an error when decompressing the stream produced by muzic, and muzic won't be able to decompress stream produced by Zlib if MZ_ZLIB_HEADER is disabled.

Zlib stream checksum

Zlib ends raw deflate stream with a 4-byte checksum conforming RFC-1950 by default. To emulate this behavior, the macro MZ_ZLIB_CHECKSUM must be enabled in mz_config.h (it's enabled by default).

Comparison with Zlib

Binary size

Tested on Linux x86_64 with gcc 11.1.0, CMake option CMAKE_BUILD_TYPE=Release

Binary	muzic	Zlib
Static library	23664B (23.1KB)	125522B (122.6KB)
examples/defl2stdout	21152B (20.7KB)	56112B (54.8KB)
examples/infl4stdin	25456B (24.9KB)	47184B (46.1KB)

Memory usage

Tested on Linux x86_64 with gcc 11.1.0, CMake option CMAKE_BUILD_TYPE=Release

Profiler: valgrind-3.18.1 with option --tool=massif --stacks=yes

Binary	muzic (stack/heap/total)	Zlib (stack/heap/total)
examples/defl2stdout	3.6KB / 33.1KB / 36.7KB	3.6KB / 262.9KB / 266.5KB
examples/infl4stdin	3.3KB / 22.0KB / 25.3KB	3.3KB / 40.0KB / 43.3KB

TODO:

• Support Z_BLOCK mode for inflate()
• Benchmarks

Credits

DEFLATE engine: part of uzlib

(c) 2014-2020 Paul Sokolovsky

INFLATE engine: Inflater

Copyright (c) 2020 Martin Rizzo